Did you know?

If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by excess weight. Please remove excess weight and check ...Just got my litter robot and I to am having this issue. It's just blinking red and green. Couldn't get the pairing yellow light to start blinking while holding the wifi button for 3 secs but the app let me continue and set up anyways. The robot is now listed in app and can be controlled via the app but the light is still flashing red and green.The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red. You will also receive a notification on your phone if you ...@Tracy, 3 Flashing LED's [Blue, Yellow, & Red] If the Litter-Robot Open Air unit cannot find Dump and or Home position, the control panel will display 3 lights blinking in several potential patterns. The lights may flash sequentially (one after the other) from left to right, right to left, or all at the same time.Slow yellow blinking light. Have tried it all..!!! Litter robot 3 was working great until last week. (This model is before the app) it started to stop mid-cycle upside down, about 11:00 position, and will blink yellow (about 1 blink per second). So far we have: replaced pinch sensors, sanded down bonnet sensors, soaked entire globe to ensure no ...The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. In this comprehensive tutorial video guide, Aiman...The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...If you have a Litter-Robot III Open Air 3 and it's stopped working with yellow blinking / flashing light and/or the globe does not rotate in normal operating cycle or spinning continuously counter clockwise in one direction, then this video might be for you.If your robot has problems with the yellow blinking light, please follow the troubleshooting below to determine whether the issue is due to excess weight, the bonnet connection, or the Anti-Pinch safety feature: *The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by …Resolve issues with your Litter-Robot 4 showing a blue light bar with partial yellow flashing. Learn how to troubleshoot excess weight detection, ensure accurate SmartScale™ readings, and update firmware for optimal performance. ... The Litter-Robot is equipped with weight sensors located in the base of the unit that are used to further ...Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Chat with us 1-877-250-7729 Submit a ticket. Learn how to troubleshoot the cat sensor on your Litter-Robot 3. Find solutions to issues with yellow flashing lights, interrupted cycles, and more.r/litterrobot. •. BootleggerBill. Help! Rapidly flashing yellow cycle light. Our LR3 connect is displaying a rapidly flashing cycle light and will not work. I have completely dissembled and deep cleaned. I paid special attention tot he pinch detector and DFI areas, making sure that the pinch detector can move freely and the DFI sensor is clean.ScyllaOfTheDepths • 1 min. ago. Yellow light blinking means you put too much litter in it. Only fill it to the fill lines. It should have come with instructions with that in them. 1. Reply. I've had nothing but constant issues with my litter robots since I got them. I have two boxes. On one of them the light is flashing yellow rapidly….Litter-Robot 3: Yellow flashing slowly (Cat sensor) The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If a cycle is interrupted or the bonnet is removed, the unit will stop, and the yellow light will flash slowly, about 1x per second.Hi @Christos93. Please check also anti-pinch pins. The Anti-Pinch safety feature is two pins connected to the motherboard that must touch each other continuously. If they are separated, you will have an alarm (yellow blinking light). The Anti-Pinch safety is located in the top back left of the Litter-Robot base.LR3 blinking red light. Recently had to replace the motor as one of the wires was severed. I replaced the motor no problem. when I turned the litter robot back on I got a blinking yellow light but the globe wouldn’t cycle. I reset everything and then I got a blinking red light. after going through all of the troubleshooting options I replaced ...Inspect the bonnet connections. Remove the bonnet by pressing the latches on both sides of the bonnet, then lift while rotating it backward; there are two plastic tabs on the back of the bonnet that should slide up and out of the base. Set the bonnet aside. When standing in front of Litter-Robot, locate the bonnet connection terminals.The yellow light flashing quickly is due to the anti-pinch feature. The Anti-Pinch safety feature is two pin connected to the motherboard that must touch each other continuously. If they are separated, you will have an alarm (yellow blinking light). The Anti-Pinch safety is located in the top back left of the Litter-Robot base.The yellow light has remained on (not flashing) and it does not respond to any activity anymore. We have taken apart all the pieces and made sure they are clean. We unplugged it for a few hours but as soon as it’s turned on again, the yellow light reappears. It does not respond to the reset, empty or power button either.Cleaned out litter in the globe grooves, just in case; Made sure cat sensor connection on the bottom was good to go (reseated, checked for issues); Removed globe and dirty litter drawer, shorted bonnet pins, cycled LR3; First time, it did the same thing (ran for a little, stopped, went back and did yellow-red seq);The yellow light has remained on (not flashStart with Litter-Robot's Feeder Robot! Find e Preparation. If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app.. You can now proceed with the onboarding process within the Whisker App to finalize connection.. When your Litter-Robot 4 has successfully …]The blinking yellow light will switch to blinking red after 2 minutes if the cat sensor (CATS) has been continuously activated by excess weight. Please remove excess weight and check your unit for the following:/:m]]The litter is above the fill line or in excess of 10lbs. /:m]]The cat sensor has not been reset after adding weight /:m] SOLUTION: I ended up having to replace the DFI kit and main circu Litter-Robot utilizes position sensors to determine the position of the globe during rotation. Additionally, the speed of the globe is calculated to ensure continued operation as a backup to the position sensors. If your unit displays a red light bar with partial white flashing, this indicates that the unit did not detect the globe position ... The yellow light flashing quickly is due to the anti

The yellow light has remained on (not flashing) and it does not respond to any activity anymore. We have taken apart all the pieces and made sure they are clean. We unplugged it for a few hours but as soon as it’s turned on again, the yellow light reappears. It does not respond to the reset, empty or power button either.The slow flashing yellow light is indicating either a bonnet removed error, or a weight change in cycle. ... Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. ... This thing powers red green and blue leds and shifts between different color combinations every 4 seconds. 220V AC are connected where i marked it ...Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. Members Online • pikabang ... Eventually it got to a point where it wouldn't cycle anymore and had a flashing yellow light, even after following every troubleshooting method I could find. Whisker sent me replacement DFI/Pinch sensors and it was working fine ...It’s super dumb but click the blue flashing option and it will give you a sequence choice of blue to yellow or blue to red. Now following the steps provided didn’t fix anything for me, …

The following troubleshooting should resolve the blue light blinking while the waste drawer is empty. Once resolved, the unit should consistently recognize when your cat visits and cycle accordingly. To troubleshoot the blue blinking: Remove the drawer from the unit and press RESET. If the unit goes to solid blue, press the CYCLE button. The unit should start its cleaning cycle and goes back ...To troubleshoot the blue blinking, let's start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged & Unplug your power supply from the base 2.) Wait 10 seconds then plug the unit back in. 3.) Allow the unit to complete a start‐up cycle.Okay, that's what I figured. Usually when rapid yellow appears, so does the flashing blue. You'll need to get a DFI replacement kit and replace the DFI sensors and the pinch detect terminals. See one of my recent posts. Just went through this, and my LR is outside warranty. I have a link to their troubleshooter listed.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. 1. Gently shake the litter box from side to side to loosen . Possible cause: Hi, my litter robot 3 is flashing yellow very quickly and it does not work. I tried .